BEG DEUTER
Pack Fitting 101
Fitting a small to mid-volume up to 50 liters
1 - Loosen all the straps on the harness system and position the hip belt so the top of the iliac crest is about 1-inch down from the top of the hip belt. Correct positioning will direct the weight onto the hips.
2 - Position the shoulder straps so there is full contact from the shoulder blade over the collar bone and across the chest. The connection point of the shoulder straps to the mesh back panel should rest between the shoulder blades.
3 - Adjust the load stabilizer straps. These come off the top of harness systems. When pulled forward, the straps will move the load closer to the back and the body's center of gravity, thus increasing the stability of the pack. Keep in mind that these are not load lifting straps, so you are not looking for a 45-degree angle from harness to pack.
4 - Adjust the sternum strap so it rides two fingers above the bottom of the sternum. (just a starting point)
Pack Fitting 101
1 - Loosen all the straps on the harness system and position the hip belt so the top of the iliac crest is about 1-inch down from the top of the hip belt. Correct positioning will direct the weight onto the hips.
2 - Position the shoulder straps so there is full contact from the shoulder blade over the collar bone and across the chest. The connection point of the shoulder straps to the mesh back panel should rest between the shoulder blades.
3 - Adjust the load stabilizer straps. These come off the top of harness systems. When pulled forward, the straps will move the load closer to the back and the body's center of gravity, thus increasing the stability of the pack. Keep in mind that these are not load lifting straps, so you are not looking for a 45-degree angle from harness to pack.
4 - Adjust the sternum strap so it rides two fingers above the bottom of the sternum. (just a starting point)
1 - Loosen all the straps on the harness system and position the hip belt so the top of the iliac crest is about 1-inch down from the top of the hip belt. Correct positioning will direct the weight onto the hips.
2 - Tighten the shoulder straps to ensure there is full contact from the shoulder blade to the collar bone.
3 - The harness should be positioned so the strap's insertion point on the pack rests between the body's shoulder blades. On packs with the Vari-Quick adjustment system the tab should be in this location.
4 - To adjust the Vari-Quick harness, undo the Velcro closure and thread through the suitable attachment loops. Tighten the Velcro and fix closed.
5 - On larger packs, this strap is commonly referred to as the Load Lifter strap. The tensioning of this strap will move the load closer to the body's back and more in line with the body's center of gravity. The angle of this strap is not the crucial criteria for a pack fit, but instead look at steps 1 and 2 for a perfect fit.
6 - The final adjustment is the positioning of the sternum strap. A good rule of thumb is 2 fingers above the bottom of the sternum. Just remember not to constrict breathing.
How to Pack your Backpack
The center of gravity should be close to the body and ideally at shoulder height. The sleeping bag generally goes into the bottom compartment, and heavy items are packed close to the back. Small items are conveniently placed in the top lid where they are quickly accessible. On easy routes, like hiking trails and flat terrain, it is advisable to carry heavy items higher up in the pack - ideally shoulder height.
The center of gravity of the backpack rests better above the hips. In difficult terrain, like alpine tours, heavy equipment should be at the center of the back. In this manner you walk rather bent forward, but don't lose your balance as easily as if you have a high point of gravity.
The center of gravity should be close to the body and ideally at shoulder height. The sleeping bag generally goes into the bottom compartment, and heavy items are packed close to the back. Small items are conveniently placed in the top lid where they are quickly accessible. On easy routes, like hiking trails and flat terrain, it is advisable to carry heavy items higher up in the pack - ideally shoulder height.
The center of gravity of the backpack rests better above the hips. In difficult terrain, like alpine tours, heavy equipment should be at the center of the back. In this manner you walk rather bent forward, but don't lose your balance as easily as if you have a high point of gravity.
Backpack Fundamentals
The manufacture of a high specification backpack relies on the use of high quality materials. Unlike cheap brands, Deuter has the advantage of choosing their own raw materials and suppliers. Regular tests in labratories guarantee the conformance of the regulations considering AZO free materials and the absense of heavy metals, etc. High quality fabrics do not guarantee a superior product. The materials also have to be effectively and creatively combined so that the different models fit the different needs of the customer to perfection. See below for a glossary of fabric terms.
The two most important components are the man-made fibers: polyester and polyamide (nylon). High density polyamide fabric is extremely abrasion resistant in a thin layer and is more robust than polyester. It is popular due to its high performance in a light weight layer. Polyester does not absorb water and does not bleach when exposed to UV rays. Most importantly, the rugged polyester fabric has a typical soft touch yet is not heavy because polyester fibers are lighter.
Texture is measured in denier (den), which is a standard measurement of the weight of 9000 meters of the thread. For example, a 600 denier thread with a length of 9000 meters has a weight of 600 grams. It means the thicker the thread, the higher the denier number. The higher the denier number, the more robust is the texture and the higher the weight per square meter.
With coatings the fabrics are made water resistant. The most important part is the quality. Deuter does not permit the use of environmentally damaging acrylics or PVC materials. On principle, Deuter only uses high quality PU (polyurethane) coatings. These coatings remain elastic and flexible and are cold and fold resistant, typically adding 40 to 70 grams per square meter to the weight. Any more coating would cause it to detach from the fabric. Additionally, Deuter fabrics are impregnated for water resistance.
According to the German industrial standard, the term "waterproof" may only be used if a material withstands a 1400mm water column. Deuter's rain covers fulfill the standard. Impregnated and coated backpack fabrics endure 700mm to 1200mm of water. In use, the PU coating ages and there are additionally a lot of seams on the backpack through which water can seep. Therefore, Deuter advises using a rain cover and to keep items that must remain dry in a plastic bag.
YKK Zippers are currently the best available on the market. These top quality zippers are very robust and reliable. Deuter has upgraded to these high-tech miracles across their pack line.
The manufacture of a high specification backpack relies on the use of high quality materials. Unlike cheap brands, Deuter has the advantage of choosing their own raw materials and suppliers. Regular tests in labratories guarantee the conformance of the regulations considering AZO free materials and the absense of heavy metals, etc. High quality fabrics do not guarantee a superior product. The materials also have to be effectively and creatively combined so that the different models fit the different needs of the customer to perfection. See below for a glossary of fabric terms.
The two most important components are the man-made fibers: polyester and polyamide (nylon). High density polyamide fabric is extremely abrasion resistant in a thin layer and is more robust than polyester. It is popular due to its high performance in a light weight layer. Polyester does not absorb water and does not bleach when exposed to UV rays. Most importantly, the rugged polyester fabric has a typical soft touch yet is not heavy because polyester fibers are lighter.
Texture is measured in denier (den), which is a standard measurement of the weight of 9000 meters of the thread. For example, a 600 denier thread with a length of 9000 meters has a weight of 600 grams. It means the thicker the thread, the higher the denier number. The higher the denier number, the more robust is the texture and the higher the weight per square meter.
With coatings the fabrics are made water resistant. The most important part is the quality. Deuter does not permit the use of environmentally damaging acrylics or PVC materials. On principle, Deuter only uses high quality PU (polyurethane) coatings. These coatings remain elastic and flexible and are cold and fold resistant, typically adding 40 to 70 grams per square meter to the weight. Any more coating would cause it to detach from the fabric. Additionally, Deuter fabrics are impregnated for water resistance.
According to the German industrial standard, the term "waterproof" may only be used if a material withstands a 1400mm water column. Deuter's rain covers fulfill the standard. Impregnated and coated backpack fabrics endure 700mm to 1200mm of water. In use, the PU coating ages and there are additionally a lot of seams on the backpack through which water can seep. Therefore, Deuter advises using a rain cover and to keep items that must remain dry in a plastic bag.
YKK Zippers are currently the best available on the market. These top quality zippers are very robust and reliable. Deuter has upgraded to these high-tech miracles across their pack line.
Know your Conversions
| Weight | Volume | Length | Liquid (volume to weight) |
|---|---|---|---|
| 1 Pound = 453.6 grams | 1 Liter = 61 cubic inches | 1 Inch = 2.54 centimeters | 1 Liter (water) = 2 pounds 5 ounces |
| 1 Pound = 0.45 kilograms | 1 Cubic Inch = 0.016 liters | 1 Centimeter = 0.394 inches | 1 Gallon (water) = 8.345 pounds |
| 1 Ounce = 28.35 grams | |||
| 1 Gram = 0.0022 pounds | |||
| 1 Gram = 0.035 ounces | |||
| 1 Kilogram = 2.2 pounds |
No comments:
Post a Comment